Numerical Analysis of the Inlet and Outlet Diameter Effects on Pulsation Dynamics and Cavitation in the Lobe Pump

Document Type : Regular Article

Authors

1 College of Metrology Measurement and Instrument, China Jiliang University, Hangzhou, 310018, China

2 Key Laboratory of River Basin Digital Twinning of Ministry of Water Resources, Beijing, 310018, China

3 School of Mechanical Engineering, Zhejiang University of Water Resources and Electric Power, Hangzhou 310018, China

Abstract

To investigate the impact of inlet and outlet diameters on the performance of lobe pumps, this paper analyses six lobe pumps with an inlet and outlet diameter ratio of 1, as well as five lobe pumps with varying inlet and outlet diameter ratios, while keeping other conditions constant. Three-dimensional unsteady numerical simulations of the pumps were conducted using the full cavitation model and the re-normalization group (RNG) k-ε turbulence model. The results show that for the lobe pumps with internal diameters between 40 mm and 100 mm, the shaft power is reduced by 17.6%, the pressure is reduced by 0.4 MPa, the pulsation coefficient is reduced by 18%, the variation of the gas volume fraction at the gap is in the range of 0.2 to 0.8, and the maximum value of the radial force in the X-direction decreases from 58.36 to 17.6 kN, and that the maximum value of the radial force in the Y-direction decreases from 14.56 to 3.25 kN. When the scale is increased from 0.6 to 1, the shaft power decreases by 25.9%, the pressure decreases by 0.1 MPa, the pulsation coefficient decreases by 6%, the volume fraction of gas at the gap varies between 0.1 and 0.8, and the maximum radial force in the X-direction decreases from 17.63 to 12.52 kN, and in the Y-direction decreases from 7.68 to 6.32 kN. This shows that choosing a suitable inner diameter can reduce the cavitation tendency of the lobe pump, enhance its anti-cavitation ability, optimize the fluid flow characteristics, and thus improve its reliability and stability.

Keywords

Main Subjects

References

Al-Obaidi, A. R. (2024a). Effect of different guide vane configurations on flow field investigation and performances of an axial pump based on CFD analysis and vibration investigation. Experimental Techniques, 48(1), 69–88. https://doi.org/10.1007/s40799-023-00641-5
Al-Obaidi, A. R. (2024b). Evaluation and investigation of hydraulic performance characteristics in an axial pump based on CFD and acoustic analysis. Processes, 12(1), 129. https://doi.org/10.3390/pr12010129
Al-Obaidi, A. R., & Alhamid, J. (2024). Analysis of unsteady internal flow characteristics in axial pump with varying number of blades using computational modelling and vibration techniques. Flow Measurement and Instrumentation, 99, 102654. https://doi.org/10.1016/j.flowmeasinst.2024.102654
Al-Obaidi, A. R., Alhamid, J., & Khalaf, H. (2024). Unsteady behaviour and plane blade angle configurations’ effects on pressure fluctuations and internal flow analysis in axial flow pumps. Alexandria Engineering Journal, 99, 83–107. https://doi.org/10.1016/j.aej.2024.04.048
Amer, M., Vaca, A., & Bowden, M. (2022). Effects of different blade numbers on radial exciting force of lobe pump rotor: Original papers. Bioprocess and Biosystems Engineering, 45(9), 1477–1488. https://doi.org/10.1007/s00449-022-02757-1
Ammendolea, D., Greco, F., Leonetti, L., Lonetti, P., & Pascuzzo, A. (2023). Fatigue crack growth simulation using the moving mesh technique. Fatigue & Fracture of Engineering Materials & Structures, 46(12), 4606–4627. https://doi.org/10.1111/ffe.14155
Bonandrini, G., Mimmi, G., & Rottenbacher, C. (2012). Design and simulation of meshing of a particular internal rotary pump. Mechanism and Machine Theory, 49, 104–116. https://doi.org/10.1016/j.mechmachtheory.2011.11.001
Chen, J., Zhang, M., Liu, T., Huang, B., Wang, Y., & Hu, C. (2024a). Experimental investigation of the influence of micro vortex generator on the bubble cavitation around a hydrofoil. Ocean Engineering, 298, 117216. https://doi.org/10.1016/j.oceaneng.2024.117216
Chen, J., Zhang, M., Liu, T., Huang, B., Wang, Y., & Hu, C. (2024b). Experimental investigation of the influence of micro vortex generator on the bubble cavitation around a hydrofoil. Ocean Engineering, 298, 117216. https://doi.org/10.1016/j.oceaneng.2024.117216
Dehghan, A. A., & Shojaeefard, M. H. (2022). Experimental and numerical optimization of a centrifugal pump volute and its effect on head and hydraulic efficiency at the best efficiency point. Proceedings of the Institution of Mechanical Engineers Part C-Journal of Mechanical Engineering Science, 236(9), 4577–4598. https://doi.org/10.1177/09544062211056019
Dehghan, A. A., Shojaeefard, M. H., & Roshanaei, M. (2024). Exploring a new criterion to determine the onset of cavitation in centrifugal pumps from energy-saving standpoint; experimental and numerical investigation. Energy, 293, 130681. https://doi.org/10.1016/j.energy.2024.130681
Gu, P., Xing, L., Wang, Y., Feng, J., & Peng, X. (2021). Transient flow field and performance analysis of a claw pump for FCVs. International Journal of Hydrogen Energy, 46(1), 984–997. https://doi.org/10.1016/j.ijhydene.2020.09.154
Hatano, S., Kang, D., Kagawa, S., Nohmi, M., & Yokota, K. (2014). Study of cavitation instabilities in double- suction centrifugal pump. International Journal of Fluid Machinery and Systems, 7(3), 94–100. https://doi.org/10.5293/IJFMS.2014.7.3.094
Jacazio, G., & De Martin, A. (2016). Influence of rotor profile geometry on the performance of an original low-pressure gerotor pump. Mechanism and Machine Theory, 100, 296–312. https://doi.org/10.1016/j.mechmachtheory.2016.02.012
Kang, Y. H., Vu, H. H., & Hsu, C. H. (2012). Factors impacting on performance of lobe pumps: a numerical evaluation. Journal of Mechanics, 28(2), 229–238. https://doi.org/10.1017/jmech.2012.26
Li, G., Sun, H., He, J., Ding, X., Zhu, W., Qin, C., Zhang, X., Zhou, X., Yang, B., & Guo, Y. (2024a). Deep learning, numerical, and experimental methods to reveal hydrodynamics performance and cavitation development in centrifugal pump. Expert Systems with Applications, 237, 121604. https://doi.org/10.1016/j.eswa.2023.121604
Li, J., Wu, T., Cheng, C., Li, J., & Zhou, K. (2024b). A Review of the research progress and application of key components in the hydrogen fuel cell system. Processes, 12(2), 249. https://doi.org/10.3390/pr12020249
Li, Y., Li, W., Ji, L., He, S., Huang, Y., Li, S., Zhai, H., Pu, W., & Li, X. (2024c). Analysis of internal flow characteristics in hydrogen circulation pump with variable trochoid ratio profile. International Journal of Hydrogen Energy, 61, 1429–1445. https://doi.org/10.1016/j.ijhydene.2024.02.288
Li, S., Li, W., Ji, L., Zhai, H., Li, Y., Wang, C., & Li, X. (2023). Effect of pressure ratio on transient flow in hydrogen circulating pump. International Journal of Hydrogen Energy, 48(69), 26937–26950. https://doi.org/10.1016/j.ijhydene.2023.03.370
Li, Y., Guo, D., & Li, X. (2019). The effect of startup modes on a vacuum lobe pump. Vacuum, 166, 170–177. https://doi.org/10.1016/j.vacuum.2019.05.009
Li, Y., Zhang, X., Guo, D., Wang, X., (2018). Numerical analysis and verification of flow characteristics of rotor cavity of spiral rotary lobe pump, Transactions of the Chinese Society of Agricultural Engineering. 2018,34(10):62-67. https://doi.org/10.11975/j.issn.1002-6819.
Liersch, C., Frankenbach, M., Froehlich, J., & Lang, J. (2014). Recent progress in designing moving meshes for complex turbulent flows. Meteorologische Zeitschrift, 23(4), 425–439. https://doi.org/10.1127/0941-2948/2014/0573
Liu, G., Liu, P. Y., Wei, W. J., Zhang, S. Y., & Li, H. T. (2012). A New design method for the rotor profile curve of the lobe pump. Advanced Materials Research, 482–484, 1196–1200. https://doi.org/10.4028/www.scientific.net/AMR.482-484.1196
Liu, Y., Wang, L., & Zhu, Z. (2015). Numerical study on flow characteristics of rotor pumps including cavitation. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 229(14), 2626–2638. https://doi.org/10.1177/0954406214562634
Luo, H., Zhou, P., Cui, J., Wang, Y., Zheng, H., & Wang, Y. (2025). Energy performance prediction of centrifugal pumps based on adaptive support vector regression. Engineering Applications of Artificial Intelligence, 145, 110247. https://doi.org/10.1016/j.engappai.2025.110247
Malekshah, E. H., Wlodzimierz, W., & Majkut, M. law. (2024). Investigation on natural to ventilated cavitation considering the air-vapor interactions by Merging theory with insight on air jet location/rate effect. International Journal of Heat and Mass Transfer, 220, 124968. https://doi.org/10.1016/j.ijheatmasstransfer.2023.124968
Matteo, L., Dazin, A., & Tauveron, N. (2019). Modelling of a centrifugal pump using the CATHARE-3 one-dimensional transient rotodynamic pump model. International Journal of Fluid Machinery and Systems, 12(2), 147–158. https://doi.org/10.5293/IJFMS.2019.12.2.147
Menendez Blanco, A., & Fernandez Oro, J. M. (2012). Unsteady numerical simulation of an air-operated piston pump for lubricating greases using dynamic meshes. Computers & Fluids, 57, 138–150. https://doi.org/10.1016/j.compfluid.2011.12.014
Meng, X., Tian, H., Yu, R., Lu, Y., Gu, X., Tan, G., & Cai, G. (2023). Three-dimensional numerical simulation of hybrid rocket motor based on dynamic mesh technology. Aerospace Science and Technology, 141, 108573. https://doi.org/10.1016/j.ast.2023.108573
Orlandi, F., Muzzioli, G., Milani, M., Paltrinieri, F., & Montorsi, L. (2023). Development of a numerical approach for the CFD simulation of a gear pump under actual operating conditions. Fluids, 8(9), 244. https://doi.org/10.3390/fluids8090244
Qiu, J. T., Li, N., Yang, C. J., Cai, Y. L., & Meng, K. Y. (2022). Numerical study on a coupled viscous and potential flow design method of axial-flow pump impeller. Ocean Engineering, 266, 112720. https://doi.org/10.1016/j.oceaneng.2022.112720
Sun, S., Wang, X., Guo, P., Wu, K., Luo, X., & Liu, G. (2022). Numerical analysis of the transient leakage flow in axial clearance of a scroll refrigeration compressor. Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, 236(1), 47–61. https://doi.org/10.1177/0954408919870910
Vande Voorde, J., Vierendeels, J., & Dick, E. (2004). Flow simulations in rotary volumetric pumps and compressors with the fictitious domain method. Journal of Computational and Applied Mathematics, 168(1–2), 491–499. https://doi.org/10.1016/j.lobe.2003.04.007
Wang, J., Liu, R., Yang, S., Li, H., Wang, Z., & Li, Q. (2018). Geometric study and simulation of an elliptical rotor profile for Roots vacuum pumps. Vacuum, 153, 168–175. https://doi.org/10.1016/j.vacuum.2018.04.014
Xu, B., Liu, Q., Zhu, Z., Gao, Y., Li, C., & Zhang, Y. (2024). Influence of the rotation speed on the internal flow characteristics of an aircraft fuel gear pump. Processes, 12(3), 576. https://doi.org/10.3390/pr12030576
Zhai, H., Li, W., Ji, L., Awais, M., Li, J., & Li, S. (2022). Profile design and performance research of hydrogen circulation pump in fuel cell system. Mechanics, 28(4), 283–293. https://doi.org/10.5755/j02.mech.31528
Zhang, Q., Feng, J., Zhang, Q., & Peng, X. (2019). Performance prediction and evaluation of the scroll-type hydrogen pump for FCVs based on CFD–Taguchi method. International Journal of Hydrogen Energy, 44(29), 15333–15343. https://doi.org/10.1016/j.ijhydene.2019.04.019
Zhao, Y., Li, G., Zhao, F., Wang, X., & Xu, W. (2023). Analysis of macroscopic cavitation characteristics of a self-excited oscillating cavitation jet nozzle. Journal of Applied Fluid Mechanics, 16(11), 2130–2141. https://doi.org/10.47176/jafm.16.11.1923
Zhou, P., Cui, J., Xiao, G., Xiang, C., Dai, J., & Zheng, S. (2023). Numerical study on cavitating flow-induced pressure fluctuations in a gerotor pump. Energies, 16(21), 7301. https://doi.org/10.3390/en16217301
Zhou, P., Wen, Z., Wang, Y., Wu, Y., Wu, D., Huang, R., & Yao, Z. (2025). Improving the energy performance of vortex pump based on whale optimization algorithm. Engineering Applications of Computational Fluid Mechanics, 19(1), 2441344. http://doi.org/10.1080/19942060.2024.2441344

Files

History

  • Received: 30 August 2024
  • Revised: 04 November 2024
  • Accepted: 14 December 2024
  • Available online: 04 March 2025

Share

How to cite

Statistics