Optimization Study of Centrifugal Fan Volute Parameters based on Non-dominated Sorting Genetic Algorithm III Algorithm

Document Type : Regular Article

Authors

1 Faculty of Mechanical and Electrical Engineering, Kunming University of Science and Technology, Kunming, Yunnan, 650500, China

2 Yunnan Provincial Key Laboratory of Advanced Equipment Intelligent Manufacturing Technology, Kunming, Yunnan, 650500, China

3 Engineering Training Center, Kunming University of Science and Technology, Kunming, Yunnan, 650500, China

10.47176/jafm.18.10.3480

Abstract

To enhance the operational effectiveness of centrifugal fans under specific operating conditions, a Backpropagation (BP) neural network, combined with a reference point-based Non-dominated Sorting Genetic Algorithm III (NSGA-III), numerical simulation, and other techniques, was employed to perform multi-objective optimization. Three structural parameters of the fan volute, volute height (h), the minimum distance between the impeller and the volute tongue (β), and the radius of the volute tongue corner (r), were selected as design variables. Two performance indicators, outlet flow rate (Q) and total pressure efficiency (η), were chosen as optimization objectives. An efficient and accurate BP neural network was established as a surrogate model for predicting volute performance, and optimal design parameter combinations were obtained using the NSGA-III algorithm. The optimization results were subsequently validated through both experimental and numerical simulations. The results demonstrated strong agreement between simulation and experimental data. The BP neural network provided highly accurate fitting and predictions, yielding a reliable surrogate model. After optimization, the centrifugal fan’s Q increased by 2.29%, and η improved by 2.96%. Furthermore, structural improvements at the fan inlet enhanced the overall flow field, leading to a 6.06% increase in Q and a 4.04% increase in η compared to the original design. Overall, the dual optimization objectives were significantly improved, successfully meeting the specific operational requirements.

Keywords

Main Subjects


Ai, W. S., & Chen, X. J. (2016). Influence of inlet angle of blades on noise from multi-blade centrifugal fans. Chinese Journal of Turbomachinery, (02), 37-41. https://doi.org/10.16492/j.fjjs.2016.02.0112
Amiet, R. K. (1976). Noise due to turbulent flow past a trailing edge, Journal of Sound and Vibration, 47 (3), 387-393. https://doi.org/10.1016/0022-460X(76)90948-2
Arun kumar, P., Senthil, P., & Naveen kumar, K. (2016). Analysing mass flow rate and noise level of blowers through Ansys CFX solver. Australian Journal of Mechanical Engineering, 15(3), 175–181. https://doi.org/10.1080/14484846.2016.1230311
Bao, Z. Y., Yu, J. Z., & Yang, S. (2020) Intelligent optimization algorithms and MATLAB examples. Beijing: Publishing House of Electronics Industry.
Bi, X. J., & Wang, C. (2019). A reference point constrained dominance-based NSGA-II algorithm. Control and Decision, 34(2), 369-376. https://doi.org/10.13195/j.kzyjc.2017.1067
Chen, C. H., Yang, Q., & Cheng, Y. (2019). Numerical study of the effect of lobe-top spacing of the worm tongue on the aerodynamic noise of centrifugal fans. Technology and Market, 25(11), 46-47. https://doi.org/10.3969/j.issn.1006-8554.2018.11.017
Chen, S. Y., Sui, X., & Wang, C. X. (2007). Three-dimensional Numerical Simulation of the Internal Flow in the Centrifugal Fan. Fluid Machinery, 35(9), 22-25. https://doi.org/10.3969/j.issn.1005-0329.2007.09.006
Deb, K., & Jain, H. (2014). An evolutionary many-objective optimization algorithm using reference-point-based nondominated sorting approach, Part I: Solving problems with box constraints. IEEE Transactions on Evolutionary Computation, 18(4), 577-601. https://doi.org/10.1109/TEVC.2013.2281535.
Deb, K., Pratap, A., Agarwal, S., & Meyarivan, T. (2022). A fast and elitist multiobjective genetic algorithm: NSGA-II. IEEE Transactions on Evolutionary Computation, 6(2), 182-197. https://doi.org/10.1109/4235.996017
Huang, C. H., & Tseng, W. C. (2016). An optimal volute spiral case design for centrifugal fan: theoretical and experimental studies. International Journal of Mechanics and Materials in Design, 12, 223–240. https://doi.org/10.1007/s10999-015-9303-4
Li, Y., Zhao, C., Lu, F. A., & Ren, G. (2012). Numerical optimization on the volute configuration of a centrifugal fan via variable helical angle. Chinese Journal of Applied Mechanics, 29(4), 398-403. https://doi.org/10.11776/cjam.29.04.A036
Li, Z. H., & Zheng X. Q. (2017). Review of design optimization methods for turbomachinery aerodynamics, Progress in Aerospace Sciences, 93, 1-23. https://doi.org/10.1016/j.paerosci.2017.05.003
Liang, L., Gong, W. Q., Liu, Y. T., & Wang, F. (2023). Multi-objective optimization and performance analysis of centrifugal compressor impeller based on the immune algorithm. Journal of Xi'an Jiaotong University, 58(02), 56-65. https://doi.org/10.7652/xjtuxb202402006
Liu, Z. Z. (2015). Investigation on plate heat transfer and resistance characteristies and stamping process of plate heat exchangers. Jinan, Shandong University.
Ma, N., Meng, J., Luo, J., & Liu, Q. (2024). Optimization of thermal-fluid-structure coupling for variable-span inflatable wings considering case correlation. Aerospace Science and Technology, 153, 109448. https://doi.org/10.1016/j.ast.2024.109448.
Martins, D. M., Albuquerque, D. M., & Pereira, J. C. (2018). On the use of polyhedral unstructured grids with a moving immersed boundary method. Computers & Fluids174, 78-88. https://doi.org/10.1016/j.compfluid.2018.07.010
Patil, S. R., Chavan, S. T., Jadhav, N. S., & Vadgeri, S. S. (2018). Effect of volute tongue clearance variation on performance of centrifugal blower by numerical and experimental analysis. Materials Today: Proceedings, 5(2), 3883-3894. https://doi.org/10.1016/j.matpr.2017.11.643
Shen, Y., Lu, Q., & Li, Y. (2023). Design criterion and analysis of hybrid-excited vernier reluctance linear machine with slot halbach PM arrays. IEEE Transactions on Industrial Electronics, 70(5), 5074-5084, https://doi.org/10.1109/TIE.2022.3183278.
Shinbara, N., Hatakeyama, M., Kodama, Y., & Hayashi, H. (1996). Characteristics of fluid dynamics and noise of a multiblade radial fan. Effects of inner diameter and the number of blades on the characteristics of fluid dynamics and noise. Nippon Kikai Gakkai Ronbunshu. B Hen (Transactions of the Japan Society of Mechanical Engineers. Part B), 62, 110-116.
Tantakitti, P., Pattana, S., & Wiratkasem, K. (2018). The performance of backward curved centrifugal fan with various impeller inlet and outlet angles. 2018 Third International Conference on Engineering Science and Innovative Technology (ESIT), (pp. 1-3). https://doi.org/10.1109/ESIT.2018.8665280
Tao, Z., Li, W., Guo, Z., Chen, Y., Song, L., & Li, J. (2024). Aerothermal optimization of a turbine rotor tip configuration based on free-form deformation approach. International Journal of Heat and Fluid Flow, 110, 109644. https://doi.org/10.1016/j.ijheatfluidflow.2024.109644.
Tong, M. Z., Chen, X., Tong, S. G., Yu, Y., Li, J. F., & Hao, G. S. (2020). Multi-objective optimization design of low specific speed centrifugal pumps based on NSGA-Ⅲ algorith. China Mechanical Engineering, 31(18), 2239-2246. https://doi.org/10.3969/j.issn.1004-132X.2020.18.012
Wang, C. L., Hu, B. B., Feng Y. M., & Liu, K. K. (2019). Multi-objective optimization of double vane pump based on radial basis neural network and particle swarm. Transactions of the Chinese Society of Agricultural Engineering (Transactions of the CSAE), 35(2), 25-32. https://doi.org/10.11975/j.issn.1002-6819.2019.02.004
Wu, Y., Dou, H. S., Wei, Y. K., Chen, X. P., Chen, Y. N., & Cao, W. B. (2002). Effect of attack angle on flow characteristic of centrifugal fan. IOP Conference Series: Materials Science and Engineering. 129(1), 012-059. https://doi.org/10.1088/1757-899X/129/1/012059
Zhang, D. S., Yang, G., Zhao, X. T., Yang, X, Q., & Gao, X. F. (2022). Optimization design of vane diffuser and volute in vertical centrifugal pump based on back propagation neural network. Transactions of the Chinese Society of Agricultural Engineering (Transactions of the CSAE), 53(04), 130-139. https://doi.org/10.6041/j.issn.1000-1298.2022.04.013
Zhang, X., Zhu, Q., Wang, S., Ma, T., Gao, S., Kong, Y., Han, Q., & Chu, F., (2025). Hybrid triboelectric-variable reluctance generator assisted wireless intelligent condition monitoring of aero-engine main bearings. Nano Energy, 136, 110721. https://doi.org/10.1016/j.nanoen.2025.110721.
Zhang, Z. J., Yu, Q. Y., Deng, Y. L., & Wu, P. (2023). Multi-factor orthogonal experimental optimization design of an industrial fan considering the clearance between impeller and casing. Fluid Machinery, 51(06), 26-32. https://doi.org/10.3969/j.issn.1005-0329.2023.06.005
Zhao, T., Zhao, C., Ren, G., & Shi, T. Q. (2012). Experimental study on the effect of inclined volute tongue on the noise reduction of centrifugal fan. Fluid Machinery, (03), 1-7. https://doi.org/10.3969/j.issn.1005-0329.2012.03.001
Zhou, S. Q., Dong, H. B., Zhang, K., Zhou, H. X., Jin, W. Y. & Wang, C. H. (2021). Optimal design of multi-blade centrifugal fan based on partial coherence analysis. Journal of Mechanical Engineering Science, 236(2), 894-907. https://doi.org/10.1177/0954406221999683
Zhou, S. Q., Wang, M., Li, Z. Y., & Zhang, S. C. (2018). Influence of volute retrofit design on performance of multi-blade centrifugal fan. Transactions of the Chinese Society for Agricultural Machinery, 49(10), 180-186+249. https://doi.org/10.6041/j.issn.1000-1298.2018.10.020
Zuo, S. G., Wei, K. J., Wu, X. D., Nie, Y. J., & Xu, S. C. (2016). Multi-objective parameter optimization of centrifugal compressor impeller with Kriging model. Transactions of the Chinese Society of Agricultural Engineering (Transactions of the CSAE), 32(2), 77-83. https://doi.org/10.11975/j.issn.1002-6819.2016.02.012